DC Input, Field Configurable Limit Alarm - Q106

OPERATION

The field configurable Q106 limit alarm setpoints can be configured for HI or LO, failsafe or nonfailsafe operation. Each of the setpoints has a respective HI or LO deadband. In a tripped condition, the setpoint is exceeded and the appropriate red LED will illuminate. The trip will reset only the process falls below the HI deadband or rises above the low deadband (see Figure 1). For proper deadband operation, the HI setpoint must always be set above the LO setpoint. In failsafe operation, the relay is energized when the process is below the HI setpoint or above the LO setpoint (opposite for non-failsafe). In the failsafe mode, a power failure results in an alarm state output.

CALIBRATION

1. After configuring the DIP switches, connect the input to a calibrated DC source and apply power. Refer to the terminal wiring in the specifications section.
2. Starting Calibration: After applying power to the unit all three LEDs will flash for approximately 10 seconds. Next, adjust the input signal level for Relay “A” setpoint, the green LED should be on. Press the CAL button and hold for four seconds (until the red LED starts flashing) to enter the calibration mode. The green LED should be on and the red Relay “A” LED should now be flashing. flashing.
3. Setpoint "A": Input the desired trip level for Relay "A", if not already done, and push the CAL button. The green LED and the red Relay "A" LED should be flashing. Note, The green LED will stop flashing when the input drops below a high setpoint or rises above an low setpoint.
4. Deadband "A": For minimum deadband (0.25% approx.), press and hold the CAL button for 4 seconds. For high setpoints lower the input level to the desired deadband point and push the CAL button. For low setpoints increase the input level (green LED turns off) to the desired deadband level and push the CAL button. The green LED should be on and the red Relay "B" LED should be flashing.
5. Setpoint “B”: Input the desired trip level for Relay “B”, and push the CAL button. The green and the red Relay “B” LED should be flashing. Note, the green LED will stop flashing when the input drops below a high setpoint or rises above a low setpoint.
6. Deadband “B”: For minimum deadband (0.25% approx.), press and hold the CAL button for 4 seconds. For high setpoints lower the input level (green LED turns off) to the desired deadband point and push the CAL button. For low setpoints increase the input level to the desired deadband level and push the CAL button. The green LED should be on and both the red LEDs should be flashing.
7. Press the CAL button one final time to exit the calibration mode. Check the setpoint and deadband to validate calibration.ployed by a growing number of advanced users. Additionally, the efficiency advantages of PC based range programming can also be realized.

RELAY PROTECTION AND EMI SUPPRESSION

When switching inductive loads, maximum relay life and transient EMI suppression is achieved using external protection (see Figures 2 and 3). Place all protection devices directly across the load and minimize all lead lengths. For AC inductive loads, place a properly rated MOV across the load in parallel with a series RC snubber. Use a 0.01 to 0.1mF pulse film capacitor (foil polypropylene recommended) of sufficient voltage, and a 47W, 1/2W carbon resistor. For DC inductive loads, place a diode across the load (PRV > DC supply, 1N4006 recommended) with (+) to cathode and (-) to anode (the RC snubber is an optional enhancement).

DYNAMIC DEADBAND

LSI circuitry in the Q106 prevents false trips by repeatedly sampling the input. The input must remain beyond the setpoint for 100 milliseconds, uninterrupted, to qualify as a valid trip condition. Likewise, the input must fall outside the deadband and remain there for 100 milliseconds to return the alarm to an untripped condition. This effectively results in a “dynamic deadband” —based on time— in addition to the normal deadband.

CONFIGURATION

Unless otherwise specified, the factory presets the Model Q106 as follows:

The AC power input accepts any AC source between 85 and 265VAC.

Note: An I/QRail is required to power the modules. A two position rail is provided. See ordering information.

WARNING: Do not attempt to change any switch settings with power applied. Severe damage will result!

1. With the module removed from the rail and not powered, snap off the face plate by lifting the right edge away from the heat sink. Note the input switch (SW1) is located under the face plate. Set positions 9 & 10 for voltage or current input (see Table1).
2. Set positions 1 through 4 of input range switch “SW1” for the desired input range (see Table 1).
3. Set position 5 of input range switch “SW1” to ON (closed) for unipolar (e.g. zero based, 0-20mA) range or OFF (open) for bipolar (e.g. -100% offset, -20 to 20mA) range (see Figure 4).
4. Set positions 6 and 7 of input range switch “SW1” to ON for a HI trip setpoint or OFF for a LO trip setpoint (see Figure 4).
5. Set position 8 of input range switch “SW1” to ON for non-failsafe operation or OFF for failsafe operation (e.g. alarm trips upon power failure).

TECHNICAL SPECIFICATION (Q106)