 |
 |
 |
 |
 |
 |
| TECHNICAL SPECIFICATION (7SF) |
|||
| Case: | ABS grey. Self-extinguishing degree V-0 according to UL-94. | ||
| Front Protection: | Designed and tested for IP65 and NEMA 4X for indoor locations (with gasket installed). | ||
| Installation: | Panel mounting by means of brackets; or DIN rail. | ||
| Rear Terminal Block: | Up to 15 screw terminals, with safety rear cover. | ||
| Dimensions: | 48 x 48 mm (1.890 x 1.890 in.) according to DIN 43700; 122 mm (4.803 in.) depth. | ||
| Weight: | 250 grams maximum (1 pound) | ||
| Power Supply | Switch Mode. 100 to 240 Vac. 50/60 Hz (+10% to -15% of the nominal value) or 24 Vac/Vdc (±10% of the nominal value). | ||
| Power Consumption: | 8 VA. | ||
| Insulation Resistance: | Greater than 100 MW according to IEC 348. | ||
| Isolation Voltage: | 1500 Vrms according to IEC 348. | ||
| D/A Conversion: | Dual slope integration. | ||
| Noise Immunity: | a) | Electrical fast transient/burst requirements: Severity Level 3 (according to IEC 801-4). | |
| b) | Electric discharge requirements: Severity Level 8 (according to IEC 801-2). | ||
| Sampling Time: | - For linear inputs - 250 ms. | ||
| - For TC or RTD inputs - 500 ms. | |||
| Accuracy: | ±0.2% full scale value @ 25 °C and nominal power supply voltage. | ||
| Common Mode Rejection Ratio:3 | 120 dB @ 50/60 Hz. | ||
| Normal Mode Rejection Ratio: | 60 dB @ 50/60 Hz. | ||
| Operating Temperature: | From 0 to 50 °C. | ||
| Storage Temperature: | From -20 to 70 °C. | ||
| Humidity: | From 20% to 85% RH non-condensing. | ||
| Protection: | a) | WATCH DOG for automatic reset. | |
| b) | DIP Switches for configuration and calibration parameters. | ||
Inputs (All inputs are factory calibrated and selectable by front keyboard.) |
|||
| Thermocouples Type: | J, K, L, R, S and N are keyboard configurable. | ||
| Engineering Units: | °C and °F keyboard configurable. | ||
| Sensor Break: | Downscale or upscale programmable. | ||
| Reference Junction: | Automatic compensation for ambient temperature between 0 and 50 °C. | ||
| Reference Junction Drift: | 0.1 °C/°C. | ||
| Input Impedance: | Greater than 1 MW. | ||
| Calibration: | According to IEC 584-1 | ||
RTD Input |
|||
| RTD Type: | Pt 100 3 wire connection. | ||
| Calibration: | According to DIN 43760. | ||
| Line Resistance: | Max 20 W/wire with no appreciable error. | ||
| Engineering Units: | °C and °F keyboard configurable. | ||
| Sensor Break: | Open sensor detection and one or more open wires. Sensor short circuit detection. | ||
| Standard Ranges: | °C | -199.9 to 400.0 °C | |
| -200 to 800 °C | |||
| °F | -199.9 to 400.0 °F | ||
| -330 to 1470 °F | |||
| NOTE: | For RTD inputs, the minimum span is 100 °C or 200 °F, which makes it possible to increase the sensitivity of the control parameters. | ||
mAdc and Vdc Linear Inputs |
|||
| mAdc Input (Standard): | 0 to 20 mAdc and 4 to 20 mAdc keyboard configurable. | ||
| Input Impedance: | Less than 5 W. | ||
| Vdc Input: | 0 to 5 Vdc and 1 to 5 Vdc, configurable. Input impedance greater than 200 KW. | ||
| 0 to 10 Vdc and 2 to 10 Vdc, configurable. Input impedance greater than 400 KW. | |||
| 0 to 60 mVdc and 12 to 60 mV, configurable. Input impedance greater than 1 MW. | |||
| Read-out: | Keyboard configurable from -1999 to 4000. | ||
| Decimal Point: | Configurable in any position | ||
Current Transformer Input for OUT 1 Heater Breakdown Detection |
|||
| (Optional, 7SF only) | This feature allows measurement of the OUT 1 load current by means of a current transformer and signals an alarm condition when the current is below a pre-programmed threshold value. | ||
| Input Range: | 50 mAac. | ||
| Scaling: | Configurable from 10 Amps to 100 Amps (with a 1 Amp step). | ||
| Resolution: | - for full scale up to 20 Amps: 0.1 Amp. | ||
| - for full scale from 21 Amps to 100 Amps: 1 Amp. | |||
| Active Period: | - for relay output: NO or NC configurable. | ||
| - for SSR output: logic level 1 or 0 configurable. | |||
| Minimum On time to perform the measurement: | 50 ms. | ||
| NOTE: | The heater breakdown detection feature precludes the use of logic inputs and external setpoint selection. | ||
Logic Inputs |
|||
| The 7SF is equipped with a logic input used to select between the main and auxiliary setpoint (SP or SP2). Use an external contact with a contact rating greater than 0.5 mA, 5Vdc. The instrument needs 100 ms to recognize a contact status variation. | |||
| NOTE: | This function excludes the current transformer input (Output 1 heater breakdown alarm). | ||
Setpoints |
|||
| Two setpoints are available: | - Main Setpoint (SP). | ||
| - Auxiliary Setpoint (SP2). | |||
| Setpoint Transfer: | Transfer between SP1 and SP2 can be driven by logic input (contact closure). The transfer can be by a step or by a ramp with two different configurable rates of change (ramp up and ramp down). | ||
| Setpoint Limiters: | Setpoint low limit and setpoint high limit are configurable. | ||
Control Action |
|||
| Algorithm: | PID + Smart AT. | ||
| Type: | One (heating) or two (heating/cooling) control outputs. | ||
| Proportional Band: | Configurable | ||
| - From 1.0% to 100.0% of the input span for process with one control output. | |||
| - From 1.5% to 100% of the input span for process with two control outputs. | |||
| Setting the PB equal to zero changes the control action to ON/OFF. | |||
| Hysteresis (for ON/OFF control action): | Configurable from 0.1% to 10.0% of the input span. | ||
| Integral Time: | Configurable from 20 seconds to 20 minutes or excluded. | ||
| Derivative Time: | Configurable from 1 second to 10 minutes or excluded. | ||
| Integral Preload: | Configurable: | - for 1 control output, from 0 to 100% of the output range. | |
| - for 2 control outputs, from -100% to +100% of the heating/cooling output range. | |||
| Out 1 (heating) Cycle Time: | From 1 to 200 seconds. | ||
| AUTO/MANUAL Mode: | Selectable by front pushbutton or logic input. | ||
| AUTO/MANUAL Transfer: | Bumpless. | ||
| Two Control Outputs (heating/cooling) | |||
| Relative Cooling Gain: | Keyboard configurable from 0.20 to 1.00. | ||
| Cooling Cycle Time: | From 1 to 200 seconds. | ||
| Overlap/Deadband: | Keyboard configurable from -20% (deadband) to +50% (overlap) of the proportional band. | ||
| Note: | By setting the proper cooling medium (air, oil or water) during configuration, the instrument will automatically set the cooling (OUT 2) parameters. | ||
Control Outputs |
|||
| Type: | Time Proportioning. | ||
| Direct/Reverse Action: | Keyboard configurable. | ||
| Output Level Indication: | Separate displays for the Output 1 level (heating) and the Output 2 level (cooling). | ||
| Output Status Indication: | Two LED indicators (OUT 1 and OUT 2) are lit when their respective output is ON. | ||
| Output Level Limiter: | - For 1 control output: From 0 to 100% of the output span. | ||
| - For 2 control outputs: From -100 to 100% of the main (heating) output span. | |||
| This function may operate at instrument startup for a configurable time. To avoid thermal shock and/or preheating, it can be left active. | |||
| Relay Outputs Output Cycle Time: | Configurable from 1 to 99 seconds. | ||
| Output 1: | SPDT contact. The selection of the NO or NC contact is made by jumper. | ||
| Contact Rating: | 3 Amps at 250 Vac on resistive load. | ||
| Output 2 (Cooling): | SPST contact with rated current 2 Amps at 250 Vac on resistive load. | ||
| Logic Voltage for SSR Driver (Output 1 Only): | |||
| Logic Level 0: | Vout less than 0.5 Vdc. | ||
| Logic Level 1: | 14 Vdc ±20% @ 17 mA max. | ||
| 24 Vdc ±20% @ 1 mA max. | |||
| Output Safety Value: | When the instrument detects an out of range or a sensor break condition, it can force the output to a configurable safety value. | ||
Output “Turn Off” Function |
|||
| This function disables the control output allowing the instrument to operate as an indicator. When control is resumed, “turn off” is disabled and the instrument will operate as follows: the integral component of the output signal will be set to zero, the soft start function will be enabled, and the alarm masking function will be enabled. | |||
Alarms |
|||
| This instrument is equipped with two independent outputs configurable as: | |||
| - Heating + Alarm 1 | |||
| - Heating + Cooling | |||
| An optional output is available as Alarm 2 or the heater breakdown alarm output. | |||
| Output Action: | Direct or reverse function configurable. | ||
| Alarm Functions: | Each alarm can be configured as process alarm, band alarm or deviation alarm. | ||
| Alarm Reset: | Automatic or manual reset programmable on each alarm. | ||
| Alarm Masking: | Each alarm can be configured as masked alarm or standard alarm. Alarm masking allows suppression of alarm indicators at startup and after a setpoint change. | ||
| Alarm Indication: | Two indicators show when the respective alarm is ON. | ||
| Alarm Outputs: | Two SPST relays. Contact rated at 2 Amps, 250 Vac on resistive load. | ||
| Process Alarm Operating Mode: | High or low configurable. | ||
| Alarm Setpoint: | Configurable in engineering units within the entire range. | ||
| Hysteresis: | Configurable from 0.1% to 10.0% of the input span. | ||
| Band Alarm Operating Mode: | Inside or outside band configurable. | ||
| Alarm Setpoint: | Configurable from 0 to 500 units. | ||
| Hysteresis: | Configurable from 0.1% to 10.0% of the input span. | ||
| Deviation Alarm Operating Mode: | High or low configurable. | ||
| Alarm Setpoint: | Configurable from -500 to +500 units. | ||
| Hysteresis: | Configurable from 0.1% to 10.0% of the input span. | ||
| Heater Breakdown Alarm | (Can be used only for instruments with heater breakdown input option.) | ||
| Operating Mode: | Low alarm. | ||
| Alarm Setpoint: | Configurable in engineering units within the readout span. | ||
Serial Interface (Optional) |
|||
| Type: | RS-485. | ||
| Protocol Type: | MODBUS, JBUS, or Barber-Colman proprietary polling/selecting. | ||
| Baud Rate: | Keyboard configurable from 600 to 19200 BAUD. | ||
| Byte Format: | 7 or 8 bit configurable. | ||
| Parity: | Even, odd or none configurable. | ||
| Stop Bit: | One. | ||
| Address: | - From 1 to 31 for Barber-Colman protocol. | ||
| - From 1 to 255 for all other protocols. | |||
| Output Voltage Levels: | According to EIA standard. | ||
