Changes since Version 6.52
- Support is added for 3200 series controllers versions
2.11 and 2.31 (VP).
Changes since Version 6.50
- This release corrects a
small number of problems which existed in the previous
version.
- iTools now supports the Eurotherm model 2704 controller,
version 6.40.
- Support is added for 3200 series controllers versions
2.10 and 2.30 (VP).
- Support is added for 3500 series controllers version
2.60.
Changes since Version 6.44
- This release corrects a
small number of problems which existed in the previous
version.
- Model 2500 Controller,
iTools now supports the Eurotherm model 2580 controller,
version 3.70.
- Model 3216i/32h8i/3204i
Indicators, iTools now supports the Eurotherm model
3216i/32h8i/3204i indicators, version 1.03.
- Mini8, iTools now supports
the Eurotherm Mini8, version 2.10.
Changes since Version 6.42
- Support is added for 3200 series controllers versions 2.09
and 2.29 (VP)
Changes since Version 6.40
- Support is added for 3500 series controllers version 2.30
- This release corrects a small number of problems which have
been present since iTools 6.00 or earlier
Changes since Version 6.20
- The Terminal Wiring Editor in iTools Engineering Studio now
supports Mini8
- iTools Wizards now support report generation at the end of
the configuration process. This facility is identical to that
included within iTools Engineering Studio
- This new Windows NT service allows the iTools OPC Server to
run at system startup time, and at any time when no user is
logged in. See separate
readme file for more information
- iTools now supports the Eurotherm model 3216i/32h8i/3204i
indicators, version 1.02
- Support is added for 3500 series controllers version 2.21
- iTools now supports the Eurotherm Mini8, version 2.00
Changes since Version 6.00
- iTools Engineering Studio includes a new Terminal Wiring
Editor, showing rear terminal connections for the following
device types: 2200 series, 2400 series, 2604, 2704, 3100 series,
3200 series, 3500 series
- The opening screens of the iTools Configuration Wizards have
been redesigned for improved ease of use
- iTools Configuration Wizards are now available from within
the iTools Engineering Studio application
- Graphical Wiring Editor now offers full support for 2604,
2704 and X26 controllers, version 5.00 and later
- Graphical Wiring Editor: new color scheme which matches the
LINtools defaults wherever possible
- Graphical Wiring Editor: wires now have a curve at each
change of direction so that it is easy to see the difference
between two wires which cross and two wires which meet at a
corner
- Graphical Wiring Editor: 'Hide Unwired Connections' on block
context menu - useful for the loop where there can be many
inputs and outputs shown which have no wire
- Graphical Wiring Editor: all changes undoable and redoable -
undo information is cleared on saving to a 3508, 3504 or Mini8
- Graphical Wiring Editor: wire tags can now be moved so that
multiple wires from a single output can be shown using tags
- Graphical Wiring Editor: 'Find Start' and 'Find End' added
to wire context menu to make finding where a wire comes from or
goes to easy
- Graphical Wiring Editor: hint for a wired input shows the
name of the parameter it is wired from
- Graphical Wiring Editor: hint for a wired output shows the
names of all the parameters it is wired to
- Graphical Wiring Editor: when placing new wires the auto
wire routing is improved
- Graphical Wiring Editor: new 'Show Wires Using Tags' item on
the block context menu toggles the tags state of attached wires
- Graphical Wiring Editor: major performance improvements
- Graphical Wiring Editor: mouse drag while holding the
spacebar or the shift key scrolls the diagram
- Graphical Wiring Editor: if there is a parameter help window
open, mouse over a monitor changes the help to that parameter's
help
- Graphical Wiring Editor: monitors now have a parameter help
context menu entry
- Programmer Editor: a number of minor usability enhancements
have been made, including automatic scaling of multiple
2604/2704 plots so that all plots can be shown simultaneously to
best effect
- iTools includes a comprehensive new help file; the same
information is also included in a new manual, available in
Acrobat PDF format on the iTools CD-ROM
- Support added for model 2604 controller, version 6.20, and
model 2704 controller, version 6.30
|
| Instrument |
|
Version |
| 3504, 3508 |
|
1.04, 1.12, 1.20, 1.21, 1.23,
1.30, 2.18, 2.19, 2.21, 2.30, 2.32, 2.33, A2.47, 2.60, 2.70 |
| 3116, 3216, 3208, 3204 |
|
1.05, 1.06, 1.07,
1.10, 1.11, 1.12, 2.02, 2.03, 2.04, 2.07, 2.08, 2.09, 2.10,
2.11, 2.24,
2.27, 2.28, 2.29, 2.30, 2.31 |
|
3216i, 32h8i, 3204i |
|
1.02, 1.03 |
| 2404, 2408, 2416 |
|
3.01, 3.05, 3.06,
A4.05, 4.09, 4.10, 4.11 (also versions 3.51, 3.55, 3.56,
4.29, 4.30, 4.31, 4.32, 4.59, 4.60, 4.61) |
| 2204e, 2208e, 2216e |
|
2.06, 3.02, 3.03, A3.52, A3.53, A3.55, A3.56, 4.01, A4.02,
A4.15 (FM unit) |
| Mini 8 |
|
1.04, 1.20, 2.00,
2.01, 2.02, 2.10, 2.30 |
| 2704 |
|
2.01, 2.04, 3.03, 3.10, 4.00, 5.00, 5.05, 5.07, 5.09, 6.00, 6.10,
6.30, 6.40 |
| 2604 |
|
1.01, 1.02, 1.03, 1.04, 2.01, 2.04, 2.05, 3.00, 5.00, 5.05, 5.07, 5.09,
6.20, 6.30 |
| X26 |
|
5.20 |
| 2116, 2132 |
|
1.20, 1.30, B1.40, B1.41, 1.43, A1.82 |
| 2500 |
|
1.04, 1.06, 2.08, 2.09, 2.10, 2.22, 3.07, 3.26, 3.27, 3.30,
3.43, 3.56, 3.60, 3.62, 4.00, 4.10, 4.21, 4.30 |
| 2408i |
|
1.00, 1.01, 2.00, 3.00, 3.02 |
| 2108i, 2116i, 2132i |
|
1.00 |
| 2204, 2208, 2216 |
|
1.30 |
| 2301 |
|
1.30 |
| T630 |
|
2.01, 2.02 |
| 6100A,
6180A, 6100XIO, 6180XIO |
|
1.0 or Greater |
| 5000B, 5100e, 5100V, 5180V (Recorders) |
|
1.5 or Greater |
|
